What Causes a Shower Head Drip | 8 Points

An occurrence that you’d find with shower heads is leakage no doubt. It could be caused by various reasons. However, the major error that people never fail to recover from is assumptions.for what causes a shower head to drip.

It could be right or wrong and this could make them spoil their shower heads even more. In fact, some tend to be carefree, so they prefer calling plumbers. In other words, most homeowners erroneously believe that all leakages need to be amended by plumbers.

Whereas, not in all situation is the professionalism of plumbers necessary. At times, you just have to find out what causes a shower head to drip and resolve the issue(s) on your own.

This would aid you to learn more about the setup of the shower head. Apart from that, it would still aid you to save more money.

Furthermore, this article would be enumerating the basic things to put into consideration whenever there is leakage on one’s shower head.

It would also be providing you with the tips that could aid an individual in repairing the shower head solely without the aid of a plumber.

So, let’s consider the 8 possible causes of drips in showerheads and how they can be repaired:

 

 

8 Things to Consider about What Causes a Shower Head to Drip:

1. Cracks

If you’re not getting a lot of water from your shower head as you used to, then the first that you’d want to find out is the possibility that it could be leaking somewhere, right?

Of course, what you’d have to do is turn off the water from the source and wait for a while before turning it on again.

At this point, you’d have to trace the channels right from the source to the faceplate of the shower head. However, provided you’re using a combination of antique pipes together with the modern ones, then you can suspect the obsolete pipes first before you think of modern ones.

And once your supposition is accurate, then you can just replace the old pipes that are cracked with new ones.

2. Clogs

At times, what could cause seepage is dirt clogging on the flat plate on the showerhead. How you’d know is that no water would be found littering/messing up the whole area, but insufficient water would either be spraying from the faceplate or some parts would be dripping.

Of course, how you’d be able to remove the clogs is by halting the function and removing the shower head first.

Thereafter, you can remove the clogs from the surface by immersing it inside lime water first before you begin to scrub off the dirt from the surface. Once you’re done, you can fix it back onto the shower head.

3. Restrictor

The restrictor is the rubber that’s found at the end of the shower head’s pipe. It is a regulator that aids in controlling the water floatation in the medium.

Water drips from this point it’s found on the pipe whenever the rubber restrictor cuts. This is most common to shower heads that don’t use O-ring.

Indeed, quite a lot of things could cause the restrictor to cut. At times, it could be because of the slackness in the elasticity of the restrictor. Also, it could still be accidental.

Therefore, always check this out and make sure you replace it when there is a need for that.

4. Diverter Valve

Diverter valve aids in changing water direction from bathtub to showerhead or vice versa. Most times, these are made of ferrous metals. Of course, this makes them susceptible to rust over time.

So, whenever, you notice that water is seeping then it could be from this joint. Once you’ve confirmed that, you now have two options to rectify it. It’s either you buy a new one or you clean it.

And you’re to clean them by removing the Hex nut and clean it by brushing it after it had been soaked in vinegar. You could even use a brush to scrub the parts that there are buildups. And once you’re done, you can fix the valve back onto it.

5. Knob

The knob that it uses could also lead to leakages, especially on showerheads with a single setting. It’s the knob that you use to operate the water flow.

The dial can be turned in 180 degrees and the increase you go, the higher the volume and pressure of the water that it sprays. It’s mostly found close to the last terminal.

Water drips from here too especially when you’re using the water at the maximum limit. In fact, water seeps from the aperture since the dial is protruded forward. The possible way to rectify this, however, is to get one that fits it so well.

6. Wrong Installation

At times, it could be from the installation. Wrong installation would cause drips in any direction. So, it’s paramount that one uses a professional in the installation of pipes. And once the installation is over, you’re expected to inspect it and be sure if the job is well done.

7. Wrong Purchase

Provided your showerhead is made of plastic, then you might need to suspect the shower head itself before you even check the extensions and pipes, especially if it’s your first time of use.

Also, if your shower head uses mineral beads, then you’d have to check the shower head whether it hasn’t cracked if you notice drips.

Many at times, overfilling the shower head could cause it. So, whenever, you discover this, then just order for another instead.

Notwithstanding, the truth of the matter is that there are ways of doing this. And that’s why it’s expedient that one reads the manual to learn how to use the product before one begins to use it. This would help one to have the safer use of the product.

8. Incompatibility

The use of tapes and cellophane in bonding two pipes of different diameters. This is an erratic concept that these materials would prevent water from seeping.

Unfortunately, these are common among house owners. And this often leads to drips either sooner or later.

Final Verdict

These are the 8 practical causes of seeping leakages in the use of shower heads. We hope you’ve not only learned what causes it but how to resolve each of them effortlessly without the aid of plumbers. We just hope that you use this info to get the best use of your product.

1 COMMENT

LEAVE A REPLY

Please enter your comment!
Please enter your name here